Slovakia
Manufacturer/ Producer
Slovakia
coated rods for perfect and leak proof joints. available coating ratio is 60/40.65/35. 70/30.75/25.80/20.
Request for a quoteSlovakia
Brazing is typically used when joining pieces of the same metal type, such as steel to steel or copper to copper..
Request for a quoteSlovakia
copper-phosphorous brazing alloy, with good flow properties. It can be used to join copper to copper or copper based base materials (e.g. bronzes / brasses), on vibration free joints. CuP7 is very fluid at brazing temperature and will penetrate into narrow gaps and tight joints. The phosphorus contained in the alloy acts as a fluxing agent, so that it is not necessary to use an additional flux when brazing copper to copper; however when joining copper based materials (e.g. bronzes / brasses) a proper flux should be used.
Request for a quoteSlovakia
Gasoline generator - 5.5 KW / 13 PS air-cooled 1-cylinder OHV 4-stroke petrol engine with 9.56kW / 13PS at 3000rpm * displacement 389cm³ Generator power (continuous / maximum): 5kW / 5.5KW at 400V * Voltage: 230 / 400V * self-exciting synchronous Fuel: unleaded petrol - tank capacity: approx. 25l * running time w. full tank at 2/3 load approx. 7.5-8h Sockets: 1x 400V; 3x 230V; 1x 12V DC voltage * electric start with battery * voltmeter Fuel gauge * including wheels for easier transport * Sound pressure level (Lpa): 73 dB (A)
Request for a quoteSlovakia
No matter where you live, power cuts can't be helped and this MTL generator would be the ideal back up system for your home. Loncin specialise in producing power with low carbon emissions and improved efficiency and the LC3000-AS fits that category perfectly. It is powered by a commercial grade 4-stroke engine with OHV (Overhead Valve) for very smooth, economic running with quieter, better performance, this generator produces 2.3/2.5KW rated power, with a maximum output of 2.5/ 2.8kw and will provide a running time of fifteen hours with the large capacity fuel tank of 18 litres, enough to keep you warm and lit generally until the power returns. With AVR (Automatic Voltage Regulation), this generator ensures that the flow of electricity is smooth and even. There are safety systems to cope with both low oil levels and overloading.
Request for a quoteSlovakia
- copper SG2 (G3Si1) wire designed for welding fine-grained steels with minimum yield strength up to 420 MPa, unalloyed structural steels with strength up to 530 MPa. - suitable for welding both fillet and butt welds in all positions. - welding is possible both in the atmosphere of mixed gases Ar / CO 2 and in pure CO 2 . - lower spatter and excellent operational properties.
Request for a quoteSlovakia
Polypropylene (PP) is a tough, rigid, and crystalline thermoplastic. It is made from propene (or propylene) monomer. This linear hydrocarbon resin is the lightest polymer among all commodity plastics. PP comes either as a homopolymer or as a copolymer and can be greatly boosted with additives.
Request for a quoteManufacturer/ Producer
Pri prachárni 20
040 11 Kosice, Slovakia - Slovakia
Germany
Swept outlet similar to ANSI B 16.19 / ANSI B 36.10 Swept outlets in pipeline construction A swept outlet is used in pipeline construction just like a welding outlet, a socket welded outlet or a threaded outlet for a 90 ° branch. A swept outlet is an alternative to the T-piece / red. In comparison to the T-piece / Red.Tee, the installation effort for a swept outlet is lower because only one hole has to be drilled into a pipe. The swept outlet can then be welded into this hole. A swept outlet differs from a welding outlet in the type of welding. While a welding outlet is only placed on the run pipe and then welded, a swept outlet is welded directly into the run pipe. Ideal stress distribution Swept outlets were developed in order to achieve the best possible stress distribution for internal pressure and pipe forces. Due to the favorable voltage level, swept outlets are often used in highly stressed pipes in the oil and gas industry.
Request for a quoteSwitzerland
The TR300 is mta’s table-top soldering robot platform. This robot is purpose-built and standardized for semi-automated applications that require point-to-point soldering. The table-top platform is a cost-effective solution to automate existing hand-soldering processes without the cost of fully-automated systems. Automating the solder process has several advantages over hand soldering. It produces highly consist joints, improved quality, higher throughput, and it requires less skill and training than hand soldering. This table-top soldering robot platform is also ideal for applications where human dexterity is required to position the parts. This is because operators can load and unload the parts in offline fixtures to minimize machine downtime. Because the TR300 is a purpose-built solution, it can support any of mta’s soldering heads without compromise. The ball-screw axis and motors provide fast repeatable motion.
Request for a quoteSwitzerland
As a complement or an alternative to wave, mini-wave and traditional selective soldering techniques, the MPS700 bottom side selective soldering machine provides maximum accessibility and meets mass production requirements of quality, reliability and cycle times. The iron head is equipped with a powerful heating element and a high precision wire feeder. The solder point positions are adjusted using a compact vision system close to the iron head. A 4-axis system guarantees quick and precise movements. The MPS700 can be equipped with mta classic soldering iron head and MSH150 soldering iron head.
Request for a quoteSwitzerland
The laser MRC500 is the larger robotic cell that supports point to point laser soldering from above. The standardized platform is based on a flexible and modular concept that can be adapted to a range of processes from fully-automated in-line to stand-alone semi-automated processes. The frame of the laser MRC500 is designed to ensure the safety of the operator during the laser soldering process. Furthermore, it also provides maximum accessibility to the working area. The laser robotic cell is only equipped with mta MLH45 laser head. The main features of our laser MRC500 include: Welded frame construction 3-axis Cartesian robot 500x500mm working area Industrial PC controller with Embedded Windows® operating system Intuitive menu-driven mta MotionEditor software
Request for a quoteCreate one request and get multiple quotes form verified suppliers.